I found this info at: It's easier to read it there. DSUB 25-P Pin 13: TXDI Digital Input for DATA Communications TX Hi-speed Data Input Type (jumper JP2005).
Input level 800 mV/600 Ohms, Max.input 1.2V Tx Low-speed Data input Type ( Jumper JP2006). Input level 40 mV/600-Ohms If the Jumper setting is 'Low-speed Data' (JP2006 jumpered), this port is usable in the AUDIO (3003000 Hz) range.
If the jumper setting is 'HI-speed Data' (JP2005 jumpered), this port is usable for 9600 bps DATA communications, because the filter and limiter are not engaged in the Audio line. Pin 14: DC OUT 13.4 V/5 V DC Output Switched 13.8V output for supplying power to an accessory (jumper JP2008).
Switched and regulated DC 5.0V output for supplying power to an accessory (jumper JP2007). Maximum output current is 200 mA Pin 15: IGN Ignition Sense feature The VX-5500 may automatically be switched to the STAND-BY mode when the vehicle's igni-tion key is turned on. Maximum current is 20 mA. This feature is only enabled on transceivers con- figured for Dual Deck operation. Ignition 13.8V Pin 16: NC NO connection A IN CCESSORY DSUB 25-Pin Operating Manual Reprint C ONNECTOR Pin 17: RX DO Digital Output for DATA Communications RX Hi-speed Data Output Type (jumper JP2003).
Output level 600 mV/10k Ohms RX Low-speed Data Output Type (jumper JP2004). Output level 200 mV/600 Ohms If the Jumper setting is 'Low-speed Data' (JP2004 jumpered), this port is usable in the AUDIO (3003000 Hz) range. If the jumper setting is 'HI-speed Data' (JP2003 jumpered), this port is usable for 9600 bps DATA communications, because the filter and limiter are not engaged in the Audio line. Pin 18: E GND Ground for all logic levels and power supply re- turn. Pins 19, 20, 21, & 22: DSUB 19, DSUB 20, DSUB 21 and DSUB 22 LOGIC level (+5V / 0V) output.
The logic output appears at these pins when the front panel's PF key is turned on. The possible programming features (use CE49) are illustrated below.
If the HA feature is assigned to these ports, a cur- rent amplifier must be connected between the Horn circuit and the port. None/A PORT/B PORT/C PORT/D PORT/E PORT/HA PORT Pin 23: EXT SQL Squelch Signal Output Open collector output. Sink current 10 mA. A Signal is present (Squelch is open): Level High No Signal is present (Squelch is closed): Open When you connect the solder jumper on JP2002, this port changes to PULL UP (5 V) output.
This status can be changed by CE49 programmer. Pin 24: SP MUTE Speaker Mute Output Open collector output. External Speaker mute on: Level High External Speaker mute off: Open Pin 25: E GND Chassis ground. Answered on Dec 15, 2017.
Not enough power. The radio requires a steady 12 VDC input, or in a vehicle, 13.2 VDC. You did not mention if this is a 25 or 50 watt radio. I guess 50 watt.
This occurs often when the wire is too thin for the amperage required. Get thick wire or the harness may not provide enough amps and it will get really, really hot! The wiring harness from Vertex is the best one. If you have checked all your wiring AND the power connections, it is less likely a programming error. Let us know! Answered on Sep 19, 2017.
First of all, technically, you can't use this radio to talk to anyone other than ham radio- that being said, if you want to proceed at your own risk. Ok, is your work radio an analog radio?
Is it narrowband FM? Is it digital MOTOTRBO? Last two will make if difficult. Digital is impossible. Next, find out the exact transmit and receive frequencies for your radio. They may not be both the same if you have a radio 'repeater' your input frequency could be 5MHz higher than your receive frequency. And last- you need to know if your system has a 'PL' tone (CTCSS, or DCS) subaudible tone that will break the squelch.
So there are several variables that you will need your plant supervisor to relay to you. You can probably get much of this info on line from radio reference. Answered on May 01, 2017. It is most likely the encoder. It sends the signal to make the radios act like pagers. Two tone radios and pagers use almost the same exact format for programming.
Has anyone worked on the base station or encoder? That is where I would start.
Do you have the Vertex software and cables? It could be called a timing setting. This may not be a simple fix. Is there a service shop nearby? We've worked on pagers over 30 years and VX 231's for 12 years.
They simply do not stop working unless someone adjusted something. Answered on Feb 13, 2017. It typically means a bad battery. The charger will still try to put a small amount of charge into the battery at a slow rate. So it may not be apparent that the battery does not have a full charge.
Make certain you have the correct transformer. Try cleaning all battery contacts, on the charger, the battery AND inside the radio where the battery contacts are. I use rubbing alcohol and Q tips. If you see corrosion, try a really, really mild sand paper and a light touch! Do not unscrew the contacts on the radio. Let us know if this helps. Answered on Jul 26, 2016.
ADMS-1C Advanced Data Management System for the FT-10, FT-40, FT-50, FT-11, FT-41, FT-51. ADMS-1DAdvanced Data Management System for the FT-10, FT-40, FT-50, FT-11, FT-41, FT-51, VX-1. ADMS-1E Advanced Data Management System for the FT-10, FT-40, FT-50, FT-11, FT-41, FT-51, VX-1 and VX-5. ADMS-1F Advanced Data Management System for the VX-110 and VX-150. ADMS-1G Advanced Data Management System for the VX-7.
ADMS-1H Advanced Data Management System for the VX-2. ADMS-1J for FT-60. ( CD ISO IMAGE ). ADMS-VX3 FOR VX-3 V3.70 (LOOKING FOR THIS PROGRAM).
ADMS-VX6 FOR VX-6 V3.70.09. ADMS-VX170 FOR VX-170.
ADMS-VX177 FOR VX-127 AND VX-177 V3.70 (LOOKING FOR THIS PROGRAM). Yaesu VHF/UHF Mobile Radios: ADMS-2C Advanced Data Management System for the FT-3000, FT-8000, and FT-8500.
ADMS-2D Advanced Data Management System for the FT-3000, FT-8000, FT-8100 and FT-8500. ADMS-2E Advanced Data Management System for the FT-90R, FT-2600. ARDTS SYSTEMS: 9026 FOR FT-90: v2.09 AND FT-2600: v2.08 ( CD DISK IMAGE ). ADMS-2F Advanced Data Management System for the FT-1500.
ADMS-2G Advanced Data Management System for the FT-7100. ( CD ISO IMAGE ). ADMS-2H Advanced Data Management System for the FT-8900. ( CD ISO IMAGE ).
ADMS-2I Advanced Data Management System for the FT-8800. ( CD ISO IMAGE ). ADMS-2J Advanced Data Management System for the FT-2800. ( CD ISO IMAGE ). ADMS-2K Advanced Data Management System for the FT-7800. ( CD ISO IMAGE ).
![]()
ADMS-4B Advanced Data Management System Programmer for the FT-857/857D and FT-897/897D. ( CD ISO IMAGE ).
ARDTS-817 DISK IMAGE FOR FT-817. ADMS-1802 FOR FT-1802 V3.50.04. ADMS-1807 FOR FT-1807 V3.70 (LOOKING FOR THIS PROGRAM). Yaesu Handheld Receivers: ADMS-3 Advanced Data Management System for the VR-500. A340 ROM WRITER PROGRAM. VHF/UHF Dual Band 32 Channel, 5Watts Portable Radio. FOR FTH-2070/PRO.
VHF/UHF Dual Band 32 Channel, 5Watts Portable Radio. FOR FTH-2070/PRO. CE-1 v.1.60 1993. VHF/UHF Dual Band 32 Channel, 5Watts Portable Radio. FOR FTH-2070/PRO.
CE-1 v1.64 1999. VHF/UHF Dual Band 32 Channel, 5Watts Portable Radio. FOR FTH-2070/PRO.
CE-2 v1.20.1990. FOR FTH-2008/7008/2009/7009. FOR FTH-2008/7008/2009/7009. FOR FTM-2001 USA 79 channel simplex. FOR FTM-2002.
CE-5 v3.00 1990. FOR FTL-1011/2011/7011. Mod: how to make from 12 channels to 24. FOR FTL-1011/2011/7011.
CE-6 v2.0 1993. CE-6 v2.10 1993. CE-6 v3.10 1994.
CE-6 v4.10 1998. CE-7 USA v.2.0. VX-1000 SERIES ( FTx 1011/2011/7011 99 CHANNELS -ALPHA ). CE-7 USA v3.3 10 Oct. ( FTx 1011/2011/7011 99 CHANNELS -ALPHA ). GENCRON USA PROGRAMMING SOFTWARE. FOR: FTL-7011.
Repeater Personalization Program. FOR VXR-5000. CE-9 v2.10 15 Sept 1995. CE-9 v2.13 04 Jan 1996.
CE-9 v2.14 28 April 1997. (VX-1000 TRUNKING MOBILE EUROPE ). CE-11-P2-P3 v.1.50. FOR: FTL- 8011. 800MHz Trunk Radio. CE-12 v1.00 FOR: VX-1000 DVI ( RADIOS FITTED WITH DIGITAL VECHICLE IDENTIFICATION SIGNALLING CONROL LOGIC UNIT AND DVI FIRMWARE ), WINDOWS PROGRAMMER.
ANI UNIT FTE-18/19 PROGRAMMER. CE-16 v.1.00. FOR VX-2A/2B. CE-19 v1.20 01 April 1998. CE-19 v1.80 Apr13 1998.
CE-19 v4.00 USA. CE-19 v4.4 USA. CE-20 v1.10 09 Jan 1998. CE-20 v2.0 1997.
CE-21 v1.01 1997. CE-22 v1.11 1998. FOR VXR-1000. FOR VXR-1000. CE-23 v2.62.00. FOR VXF-20 A/B.
CE-25 v1.09 FOR VXA-100. CE-26 v1.10 PCPROGRAMMING TOOL FOR VTP-40/50.
CE-27 v1.02 1998. FOR VXR-7000. CE-27 v1.05 1998.
FOR VXR-7000. CE-27 v1.05 1998. HAM BAND FOR VXR-7000. FOR VXR-7000. FOR VXR-7000. CE-28 v01.09.
FOR F5D-11 & F5D-12 SIGTEC TONE MODULES FOR VX-10 PORTABLE RADIO. CE-29 FOR VX-210 v1.00. CE-31FW v1.05W USA.
CE-31 v1.11 USA. CE-31 v1.12 USA. CE-31 v1.14 USA. CE-31 v1.20 USA. FOR VX-800/900. SVC31 V1.00 SERVICE ALIGNMENT FOR VX-800 CE-32 v1.00 FOR VXA-120.
CE-35 v2.2.60. FOR VX-4000, VX-6000. FOR VX-520v/u. CE-39 v1.04 (USA). FOR VX-600/900. CE-39 v1.02W USA. USDA FORESTRY FOR WINDOWS.
CE-39 v1.15 USA. FOR VX-600/900. CE-39 v1.21 USA. FOR VX-600/900. FOR VX-600/900. FOR VX-600/900.
CE-39USDA v2.04. FIELD PROG SOFT FOR FIELD PROGRAMMABLE RADIOS. USDA FORESTRY FOR WINDOWS. CE-39USDA v2.07. FIELD PROG SOFT FOR FIELD PROGRAMMABLE RADIOS. USDA FORESTRY FOR WINDOWS. SVC-39 v1.00.
Kia Carnival diesel ngebul parah dalam proses perbaikan di bengkel rupin Grogol Penatus Petanahan. Kekurangan kia carnival diesel manual.
FOR VX-600/900 DOS ALIGN SOFT. FW2WIN V1.06 WITH FIRMWARE VX-900 V1.53 PACKAGE. FOR VX-146/246. CE-41 v1.00 USA. FOR VXA-210A.
CE-44 v1.00W. FOR VX-160/180. CE-44 v1.01W. FOR VX-160/180. CE-44 v1.08W USA. FOR VX-160/180.
CE44 V2.00 USA. FOR VX-160/180,(VISTA WINDOWS). CE-45 v1.00 USA. CE-45 v1.04W USA. CE-45 v1.07W USA. FOR VX-2500 LTR SERIES CE-47 BETA V1.09D (VX2500).
FOR VX-2500 LTR SERIES CE-47. FOR VX-2500 LTR SERIES. FOR VX-2500 LTR SERIES. FOR VX-2500 LTR SERIES. SVC-47 v1.00 ADJUSTMENT SOFTWARE. FOR VX-2500 LTR SERIES.
CE-49 v3.1.1.0. FOR VX-4000/5500/6000.
CE-49 v3.3.0.0. FOR VX-4000/5500/6000. CE-49 v3.3.7.0.
FOR VX-4000/5500/6000. CE-49 v4.0.6.0 FOR VX-4000/5500/6000. CVS-49 v16.8.0. FOR VX-4000/5500/6000. RADIO ADJUSTMENT.
CE-49 v1.0.2.0. FIELD PROGRAMMER FOR VX-4000/5500/6000. CE-49 v5.00 FOR VX-4000/5500/6000 (WINDOWS VISTA) NEW! FDUP FOR RF DECK FIRMWARE V3.04. FDUP FOR RF DECK FIRMWARE V4.08. SVC49 V1.6.8.0 (VX-4000, VX-6000, VX-5500) ADJUSTMENT SOFTWARE.
FW2WIN V1.08 FOR VX-4200 FIRMWARE V1.55 PACKAGE. CE-51 v 2.00W by Vertex - 2002. FOR VX-160E/180E - Europe. CE-51 v 4.01W by Vertex.
FOR VX-160E/180E - Europe. CE-51 v 5.00 by Vertex.
FOR VX-160E/180E - Europe. FOR VX-3200/2500 CONVENTIONAL. CE-52C V1.10. (VX-3208 & VX-2508 CHINA). CE-52EV v3.00B.
FOR VX-3200/2500 CONVENTIONAL. This clone editor CE52EV 3.00b has been modified to be able to program the special frequency channel to the VX-3200 radio as follows, = July 17th, 2003 Expanded the range of acceptable frequency as follows: 1. VHF C band: 148 - 174MHz - 130 - 200MHz (Ver 3.00b)@ 2. UHF D band: 450 - 490MHz - 430 - 490MHz (Ver 3.00b) 3. Delete frequency restriction beteen 406.000 - 406.100MHz CE-52E v4.41. FOR VX-3200/2500 CONVENTIONAL.
CE-52E v4.50. FOR VX-3200/2500 CONVENTIONAL. CE-52E v4.71. FOR VX-3200/2500 CONVENTIONAL. SVC-52 v1.02. ADJUSTMENT SOFTWARE FOR VX-3200/2500 CONVENTIONAL. FW2S V1.33 FLASH ROM WRITING SOFT WITH VX-3200 FIRMWARE: 39ST0372 (V0372) PACKAGE.
CE-53 v1.00W. CE-56 v1.00W-USA. CE-59 v1.0W USA. FOR VX-4100E/4200E/VX820/VX920 SERIES. CE-59 v1.01W USA.
FOR VX-4100E/4200E/VX820/VX920 SERIES. CE-59 v1.20.00W USA.
FOR VX-4100E/4200E/VX820/VX920 SERIES. CE-59 v2.10.00W USA. FOR VX-4100E/4200E/VX820/VX920 SERIES. CE-59 v2.14.00W USA. FOR VX-4100E/4200E/VX820/VX920 SERIES. CE-59 v2.29.00W USA.
FOR VX-4100E/4200E/VX820/VX920 SERIES. CE-59 v3.00 VISTA USA.
FOR VX-4100E/4200E/VX820/VX920 SERIES 2008 NEW! CE-60 v1.00W USA. FOR VXR-9000. CE-60 v1.03W USA. FOR VXR-9000. CE-60 v1.04W USA. FOR VXR-9000.
CE-60 v1.05W USA. FOR VXR-9000. FOR VXR-9000. NEW FDUP FOR VXR-9000 V1.30.
(FIRMWARE UPDATE TO V1.30). CE-62 LOOKING FOR THIS PROGRAM! FOR VX-2500E EUROPE. CE-64 v1.00W USA. FOR VX-410/414/417/420/424/427. FOR VX-410/414/417/420/424/427. FOR VX-410/414/417/420/424/427.
FOR VX-410/414/417/420/424/427. FOR VX-410/VX-420 SERIES.
FW2WIN V1.08 WITH AC050 V115 FIRMWARE PACKAGE FOR VX-410 SERIES. CE-65 v1.00W USA. FOR VX-530 SERIES. CE-65 v1.02W USA.
FOR VX-530 SERIES. SVC65 V1.00 SERVICE ALIGNMENT SOFTWARE FOR VX-530 SERIES. FW2WIN V1.06 WITH AC052 V105 FIRMWARE PACKAGE FOR VX-530 SERIES. CE-68 v1.1 USA & EUROPE.
FOR HX-270 & HX-370 SERIES. CE-71 v1.00 W, USA.
FOR VXA300 SERIES. CE-73 v1.04W USA.
VMDE-200 MDC1200 ENCODER/DECODER MODULE & VME-100 THE VME-100 IS A PLUG-IN ANI ENCODER CAPABLE OF ENCODING MDC1200, GE STAR OR DTMF ANI. CE-73 v1.05W USA. VMDE-200 MDC1200 ENCODER/DECODER MODULE & VME-100 THE VME-100 IS A PLUG-IN ANI ENCODER CAPABLE OF ENCODING MDC1200, GE STAR OR DTMF ANI.
CE-74 v1.00W USA. CE-75 v1.02W USA. CE-76 v2.01.13W USA. FOR VX7100, VX7200, VXP820/920 (APCO 25).
CE-76 v2.01.22W USA. FOR VX7100, VX7200, VXP820/920 (APCO 25). CE-76 v2.02.W USA.
FOR VX7100, VX7200, VXP820/920 (APCO 25). CE-76 v2.03.10.W USA. FOR VX7100, VX7200, VXP820/920 (APCO 25). FW2WIN P924V0109 (FIRMWARE FOR CE-76). CE-77 v1.0.0.0 FOR VX1700.
CE-77 v1.1.0.0 FOR VX1700. FSW001 V1.02 (FIRMWARE FOR VX-1700). FOR VX427AE (VX420A SERIES-256 CHANNELS) NEW CE-82 v1.02w USA. FOR VX-2100/VX-2200. CE-82 v1.03w USA. FOR VX-2100/VX-2200. CE-82 v1.04w USA.
FOR VX-2100/VX-2200. CE-82 v1.08w USA. FOR VX-2100/VX-2200.
CE-82 v1.09w USA. FOR VX-2100/VX-2200CB MOBILES. CE-82 v1.10w USA. FOR VX-2100/VX-2200CB MOBILES.
CE-82 v1.12w USA. FOR VX-2100/VX-2200CB MOBILES. CE-82 v2.00w USA. FOR VX-2100/VX-2200CB MOBILES. NEW FW2WIN V1.08 WITH FIRMWARE VX-2100 & 2200 V1.01 PACKAGE.
CE-86 v1.01w USA. CE-86 v2.0 USA. CE-86 v2.01 USA. FOR VX-350CHN (VX351 & VX354 CHINA). NEW CE-86 v2.02 USA. NEW CE-88 v1.00w USA. NEW CE-89 v1.03.
FOR VXA-420A PASSPORT SERIES PORTABLES. NEW CE-91F v1.02 FOR VX-426CB HANDY RADIO. LOOKING FOR THIS PROGRAM. NEW CE-95 v1.01 FOR VX-351 - PMR446-500mW-EUROPE.
(FOR VISTA), 2008. NEW VX-2100/VX2200 FW2WIN v1.10 FIRMWARE UPGRADE TOOL v1.09. NEW FDUP FOR RF DECK FW ( VX-4000/6000 RF DECK FIRMWARE UPDATE verx.
Xx to ver 2.2.0 ). FDUP FOR CONTROL HEAD FW ( VX-4000/6000 PANEL FIRMWARE UPDATE verx. Xx to ver 2.0.1 ). FIRMWARE TOOL UPGRADE FOR VX-600/800/900 RADIOS. NEEDS FIF-8 FLASH ROM ADAPTER. FDUP VX4000/VX6000 series RF Deck Firmware Update verx. Xx to ver4.2 2008 PFDUP VX4000/VX6000 series Panel Firmware Update verx.xx to ver3.04 2008 FT-10 Programmer.
RT Systems, Inc. FT-11 Programmer. RT Systems, Inc. FT-50 v.1.04. FT-50 v.1.05.
FT-50 v.1.07. FT-50-TOOLS v1.0 1999. FT-50 Manager. Goran Vlaski. FT-51 Programmer.
RT Systems, Inc. FT-90 Radio Programming Trial Version. By RT Systems, Inc.
FT-212/712 CAT Program v3.1. Dos and Windows. FT-736R YASCAN-11. FT-757GX MARK I CAT v1.0. FT-767GX CAT Program v1.0 4 Feb 1990.
FT-676GX CAT Tuning Program by WA3AKK. 31 March 1996. FT-920 Scope v1.0.
FT-920 Scan920. FT-980 CAT980 by K5EF. FT-990 CAT Program for FT-990/890/840/900/920/1000MP. DOS and WIN 3.1,for WIN95-exit Windows. FT-1000m3 simple program for the FT-1000 transceiver. FT-2600 TRIAL PROGRAM v1.00 2000. FT-3000 Programmer.
RT Systems,Inc. FT-7800 FTB7800 ( ID & REGISTRATION KEY INCLUDED ). FT-8100 v2.03 1999. FT-8500 v1.00 1995. FTC-2640 calculation program. GX-1710 v1.10 9 Jan 1998.
GX-2000 ROM WRITER Program A340P. GX-2000 ROM WRITER v1.9. GX-3000 U/V/K-HX400 U/V/K v1.6. GX-3000 v/u Windows editor. GX-3010DP v1.7. (Trunk Mobile 800MHz Motorola & Johnson Systems). GX-3030TJ v2.0.
Firmware version: N2.0 (Trunk 800MHz). GX-3030TM v1.0. (Trunk 800MHz). GX-4800UT (F3) ADJUSTMENT MENU FOR THE GX4800UT v1.20. GX4800UT Trunking Software v1.4 Copyright (c) 1997. GX4800UT Trunking Software v1.6 Copyright (c) 1997.
GX4800UT Trunking Software v2.0 Copyright (c) 1998. GX4800UT with PassPort Trunking Software v1.0 Copyright (c) 1999. GX5800T Trunking Software v1.3 Copyright (c) 1995. ADJUSTMENT FOR THE GX5800T. GX-5810T TUNE v0.0 GX-5810T TUNE v1.0. GX-5810T+ v1.2 (Trunk 800MHz).
GX-5810T v1.3. (Trunk 800MHz). GX-5850T Trunking Software. HX-120V/HX-120U v1.31. HX-140 v1.00 1998.
HX-240U/V v1.9. 1992 (PPS-240). HX-241U/V v1.5 1992.
HX-260 PPS v1.03. ( BUILD-0015 ). HX-290U/V v1.00 (PPS-290) 1998. HX-290U/V v1.00 (PPS-290) 1999. HX-292UT TRUNK PERSONAL PROGRAMMING SYSTEM, v1.11 MARANTZ JAPAN, ( MODELS: F1/F3/F5/SP ). HX-381 PPS Rel.1.0. HX345 & GX2010 v6.
HX340 v1.7 PPS340. HX347 v4.00 ( STANDARD VX347 FOR U.K.
HX347 v6.00 ( STANDARD VX347 FOR U.K. HX-381 PPS Rel.2.2 HX-390-A/B/C/D/E/F FORMAT PROGRAM Rel.1.2. HX-390-A/B/C/D/E/F FORMAT PROGRAM Rel.1.3. SC-390 STABO (RE-BADGED STANDARD HX390) V1.2 & V1.3 GERMAN Programm. SC-390 STABO (RE-BADGED STANDARD HX390) V1.4MH GERMAN. HX-428UT TUNE v1.1. HX-530U/V v1.0 (PPS-530) 1990.
HX-580T v1.0. HX-580T-TUNE v.1.2. HX-580T v1.5. HX-580T v2.8. HX-580T v2.9.
HX-581T v1.8. HX-582T v1.7. HX-585T TUNE v1.1. HX-585T v1.0. HX-590T TUNE v2.0. HX-591T UHF 8XX MHZ PROGRAMMER.
PL-2303 USB DRIVER SOFTWARE. PPS-340U/V v1.5 for HX-340/347V(TB)Communique London U.K. PPS-340U/V v1.7 for HX-340/347V(TB)Communique London U.K. PPS-340U/V v4.5. Release: 1992. PPS-341 v1.1.
for HX-341/347+ PPS-440U/V v1.0 for HX-440 1991. PPS-440U/V v1.7. PPS-440U/V v1.9 for HX-440 1992.
PPS-530U/V v4.0 for HX-530 1990. PPS-1500U/V v1.0 Release: 1990. PPS -1500U/V for GX-1500 v1.3 1991.
PPS -1500U/V for GX-1500 v1.5 1991. PPS-1500U/V for GX-1500 v4.4. PPS-1510U/V Trunking v2.06b 14 May 1996. PPS-1510U/V for GX-1510U/V v2.08b. 23 Sept 1996.
PPS-2000U/V v1.0. PPS-2000U/V v1.5. For GX-2000/2007U(TB)Communique London U.K. PPS-2000U/V v4.3. PPS-3200U/V v1.7 1992.
PPS-3200U/V v1.9 1992. PPS-RPT Repeater Programming Utility. For: RPT-31/32/34/33/38 RTL-2007 PROGRAMMER, 1997. ( SMC-2516/SMC-2546, USES FYG-4 PROGRAMMER ). S.C.C.DAT v1.5. SPARE PARTS ENQUIRY.
SMC2546L8 (UHF) OR SMC2516L8 (VHF) SPECIAL WIDE BAND VERSION SOFTWARE. FYG-4 EMULATOR MK II. VR-120 commander VR-500 commander VR-500 ADMS-3 v1.05 RTSystems VR-5000 Scanning Receiver Control Program VR5K v beta0.9.6. VX-3 FTBVX3 v1.10. MEMEORY MANAGEMENT BY G4HFG (USERNAME & PASSWORD INCLUDED). VX-5R/VX-1R/FT-50 Programmer.
VX-5 EASY EDITOR by KF4FDT v1.70. VX-7 Commander v1.0 beta 10. VX-7 Commander v1.26.
VX-110/150 Programmer for Windows 95/98, v1.04 2000. VX-110/150 ARDTS-150, Amateur Radio Data Transfer System v1.01 1999.
RT-Systems Inc. VX-310 PPS v1.01. VX-429 - 2509PRO MPT1327 V1.15. (350-390 MHZ LOW POWER HANDHELD FOR CHINESE POLICE).
Vertex Ce59 Software Download
VERTEX Programming Software v6.22. VERTEX Programming Software v6.24 for FTH-2070/FTH-2008/7008/2009/7009/VX-500-Vhf-Uhf/FTL-1011/2011/7011-4/1/24/99 Channels/FTL-8011- P3/P2/VX-200-VHF/UHF/VX-5000-Repeater-Vhf-Uhf. VERTEX Programming Software v7.2 for FTH-2070/VX-200/VX-500/FTL-1011/2011/7011-4/12/24 Channel/FTL-1011/2011/7011-99 Channel/VXR-5000 Repeater/VX-2000/VX-3000. VERTEX-ANTRACIT-RPS-CT42A for: VX-10-ce14/VX-300-ce18/VX-160-180-ce44/VX-400-ce24/VX-400 ALIGMENT.
If you're trying to make changes, use a program like windows enabler (search for WindowsEnablerv1.1). You can mod freqs etc.
Use the CE59 to read the radio, SAVE, then use enabler to mod what you want Common - Hardware (I've had ok results going 450 to 440), SAVE with a different name, then write back to the radio. The other way (which worked on older versions3 and I think 4) is to add a -manu to the Target of the shortcut.
Open and you get a password prompt enter ansho-bango for the password. I haven't messed with programming in a LONG while.
I only have V5.04 which the -manu does not work on. If you're trying to make changes, use a program like windows enabler (search for WindowsEnablerv1.1). You can mod freqs etc. Use the CE59 to read the radio, SAVE, then use enabler to mod what you want Common - Hardware (I've had ok results going 450 to 440), SAVE with a different name, then write back to the radio. The other way (which worked on older versions3 and I think 4) is to add a -manu to the Target of the shortcut. Open and you get a password prompt enter ansho-bango for the password.
I haven't messed with programming in a LONG while. I only have V5.04 which the -manu does not work on.radiotinkerer1 is correct about the Manufacture Mode not working on the newer versions of CE59. I am not sure which version it stops working on but here is how to access it on the older versions. Install CE59 normally. Go to “CE59 for Windows” folder. It will be in C: Vertex Standard, C: Program Files Vertex Standard, or C: Program Files (x86) Vertex Standard, depending on your operating system.
Right click on CE59Win.exe and select “Create Shortcut”. Right click on the newly created shortcut and select “Properties”. In the Target field add -manu (with being a space) at the end of the string. Click “Apply” and then “OK”. Double click on shortcut and in Password box enter “Developer Only” (no quotes) and click “OK” to start CE59 in Manufacture Mode.
Clicking cancel, or entering the wrong password 3 times, will start CE59 in regular mode. Radiotinkerer1 is correct about the Manufacture Mode not working on the newer versions of CE59. I am not sure which version it stops working on but here is how to access it on the older versions. Install CE59 normally.
Go to “CE59 for Windows” folder. It will be in C: Vertex Standard, C: Program Files Vertex Standard, or C: Program Files (x86) Vertex Standard, depending on your operating system.
Right click on CE59Win.exe and select “Create Shortcut”. Right click on the newly created shortcut and select “Properties”. In the Target field add -manu (with being a space) at the end of the string. Click “Apply” and then “OK”.
Double click on shortcut and in Password box enter “Developer Only” (no quotes) and click “OK” to start CE59 in Manufacture Mode. Clicking cancel, or entering the wrong password 3 times, will start CE59 in regular mode.I can confirm this works on CE59 EXP V4.02 However neither of the methods permanently store the band limits in the radio. You must save a codeplug and use it to program your radio otherwise if you read the radio it sets all OOB freqs to 450MHz. A nice FULL write up by garrettramsey21. MOTechGuy you're correct about the OOB codeplug being radio specific. I THINK I had a read workaround.
I believe I modded the defaultud.c59 file with OOB of 440, then saved it and it didn't blank everything back to 450 on read. If someone wants to try that, cool. I can also dig out the XP computer in a few days.Edit - I just tried the Windows Enabler to edit the bandwidth on 5.04 and if you modify the defaultud.c59 and defaultua.c59 files for OOB (they're write protected so you'll need to change that) AND the codeplug you can read from a modified radio without losing the OOB programming. The range I've got for the ua is 400-480 and the ud is 430-520.
I think everyone is aware that the VCO lockup will be a lot less than these wide ranges and if you've got a flashing display, you're certainly not locked. A nice FULL write up by garrettramsey21. MOTechGuy you're correct about the OOB codeplug being radio specific. I THINK I had a read workaround. I believe I modded the defaultud.c59 file with OOB of 440, then saved it and it didn't blank everything back to 450 on read. If someone wants to try that, cool.
I can also dig out the XP computer in a few days.Edit - I just tried the Windows Enabler to edit the bandwidth on 5.04 and if you modify the defaultud.c59 and defaultua.c59 files for OOB (they're write protected so you'll need to change that) AND the codeplug you can read from a modified radio without losing the OOB programming. The range I've got for the ua is 400-480 and the ud is 430-520.
I think everyone is aware that the VCO lockup will be a lot less than these wide ranges and if you've got a flashing display, you're certainly not locked.Thanks for that info! The VCO locks on my VX-4207 all the way to 442.775MHz so far haven't tried below that.
Yaesu Vertex Programming Software Yaesu, Standard, Vertex, Stabo, etc. YAESU-VERTEX-STANDARD-MARANTZ: Yaesu Handheld Radios: ADMS-1C Advanced Data Management System for the FT-10, FT-40, FT-50, FT-11, FT-41, FT-51. ADMS-1DAdvanced Data Management System for the FT-10, FT-40, FT-50, FT-11, FT-41, FT-51, VX-1. ADMS-1E Advanced Data Management System for the FT-10, FT-40, FT-50, FT-11, FT-41, FT-51, VX-1 and VX-5. ADMS-1F Advanced Data Management System for the VX-110 and VX-150. ADMS-1G Advanced Data Management System for the VX-7. ADMS-1H Advanced Data Management System for the VX-2.
ADMS-1J for FT-60. ( CD ISO IMAGE ).
ADMS-VX3 FOR VX-3 V3.70 (LOOKING FOR THIS PROGRAM). ADMS-VX6 FOR VX-6 V3.70.09. ADMS-VX170 FOR VX-170. ADMS-VX177 FOR VX-127 AND VX-177 V3.70 (LOOKING FOR THIS PROGRAM). Yaesu VHF/UHF Mobile Radios: ADMS-2C Advanced Data Management System for the FT-3000, FT-8000, and FT-8500. ADMS-2D Advanced Data Management System for the FT-3000, FT-8000, FT-8100 and FT-8500.
ADMS-2E Advanced Data Management System for the FT-90R, FT-2600. ARDTS SYSTEMS: 9026 FOR FT-90: v2.09 AND FT-2600: v2.08 ( CD DISK IMAGE ). ADMS-2F Advanced Data Management System for the FT-1500. ADMS-2G Advanced Data Management System for the FT-7100. ( CD ISO IMAGE ). ADMS-2H Advanced Data Management System for the FT-8900. ( CD ISO IMAGE ).
ADMS-2I Advanced Data Management System for the FT-8800. ( CD ISO IMAGE ). ADMS-2J Advanced Data Management System for the FT-2800. ( CD ISO IMAGE ).
ADMS-2K Advanced Data Management System for the FT-7800. ( CD ISO IMAGE ). ADMS-4B Advanced Data Management System Programmer for the FT-857/857D and FT-897/897D. ( CD ISO IMAGE ). ARDTS-817 DISK IMAGE FOR FT-817. ADMS-1802 FOR FT-1802 V3.50.04.
ADMS-1807 FOR FT-1807 V3.70 (LOOKING FOR THIS PROGRAM). Yaesu Handheld Receivers: ADMS-3 Advanced Data Management System for the VR-500. A340 ROM WRITER PROGRAM. VHF/UHF Dual Band 32 Channel, 5Watts Portable Radio. FOR FTH-2070/PRO. VHF/UHF Dual Band 32 Channel, 5Watts Portable Radio. FOR FTH-2070/PRO.
CE-1 v.1.60 1993. VHF/UHF Dual Band 32 Channel, 5Watts Portable Radio.
FOR FTH-2070/PRO. CE-1 v1.64 1999.
VHF/UHF Dual Band 32 Channel, 5Watts Portable Radio. FOR FTH-2070/PRO. CE-2 v1.20.1990. FOR FTH-2008/7008/2009/7009. FOR FTH-2008/7008/2009/7009. FOR FTM-2001 USA 79 channel simplex. FOR FTM-2002.
CE-5 v3.00 1990. FOR FTL-1011/2011/7011. Mod: how to make from 12 channels to 24.
FOR FTL-1011/2011/7011. CE-6 v2.0 1993. CE-6 v2.10 1993. CE-6 v3.10 1994. CE-6 v4.10 1998. CE-7 USA v.2.0. VX-1000 SERIES ( FTx 1011/2011/7011 99 CHANNELS -ALPHA ).
CE-7 USA v3.3 10 Oct. ( FTx 1011/2011/7011 99 CHANNELS -ALPHA ). GENCRON USA PROGRAMMING SOFTWARE. FOR: FTL-7011. Repeater Personalization Program. FOR VXR-5000.
CE-9 v2.10 15 Sept 1995. CE-9 v2.13 04 Jan 1996. CE-9 v2.14 28 April 1997. (VX-1000 TRUNKING MOBILE EUROPE ).
CE-11-P2-P3 v.1.50. FOR: FTL- 8011. 800MHz Trunk Radio.
CE-12 v1.00 FOR: VX-1000 DVI ( RADIOS FITTED WITH DIGITAL VECHICLE IDENTIFICATION SIGNALLING CONROL LOGIC UNIT AND DVI FIRMWARE ), WINDOWS PROGRAMMER. ANI UNIT FTE-18/19 PROGRAMMER. CE-16 v.1.00.
FOR VX-2A/2B. CE-19 v1.20 01 April 1998. CE-19 v1.80 Apr13 1998. CE-19 v4.00 USA. CE-19 v4.4 USA.
CE-20 v1.10 09 Jan 1998. CE-20 v2.0 1997. CE-21 v1.01 1997. CE-22 v1.11 1998. FOR VXR-1000. FOR VXR-1000. CE-23 v2.62.00.
FOR VXF-20 A/B. CE-25 v1.09 FOR VXA-100. CE-26 v1.10 PCPROGRAMMING TOOL FOR VTP-40/50. CE-27 v1.02 1998. FOR VXR-7000.
CE-27 v1.05 1998. FOR VXR-7000. CE-27 v1.05 1998. HAM BAND FOR VXR-7000. FOR VXR-7000.
FOR VXR-7000. CE-28 v01.09. FOR F5D-11 & F5D-12 SIGTEC TONE MODULES FOR VX-10 PORTABLE RADIO. CE-29 FOR VX-210 v1.00. CE-31FW v1.05W USA. CE-31 v1.11 USA.
CE-31 v1.12 USA. CE-31 v1.14 USA. CE-31 v1.20 USA. FOR VX-800/900.
SVC31 V1.00 SERVICE ALIGNMENT FOR VX-800 CE-32 v1.00 FOR VXA-120. CE-35 v2.2.60. FOR VX-4000, VX-6000. FOR VX-520v/u.
CE-39 v1.04 (USA). FOR VX-600/900. CE-39 v1.02W USA.
![]()
USDA FORESTRY FOR WINDOWS. CE-39 v1.15 USA. FOR VX-600/900. CE-39 v1.21 USA. FOR VX-600/900.
FOR VX-600/900. FOR VX-600/900. CE-39USDA v2.04. FIELD PROG SOFT FOR FIELD PROGRAMMABLE RADIOS. USDA FORESTRY FOR WINDOWS.
CE-39USDA v2.07. FIELD PROG SOFT FOR FIELD PROGRAMMABLE RADIOS. USDA FORESTRY FOR WINDOWS. SVC-39 v1.00.
FOR VX-600/900 DOS ALIGN SOFT. FW2WIN V1.06 WITH FIRMWARE VX-900 V1.53 PACKAGE. FOR VX-146/246. CE-41 v1.00 USA.
FOR VXA-210A. CE-44 v1.00W.
FOR VX-160/180. CE-44 v1.01W. FOR VX-160/180. CE-44 v1.08W USA. FOR VX-160/180. CE44 V2.00 USA. FOR VX-160/180,(VISTA WINDOWS).
CE-45 v1.00 USA. CE-45 v1.04W USA. CE-45 v1.07W USA. FOR VX-2500 LTR SERIES CE-47 BETA V1.09D (VX2500). FOR VX-2500 LTR SERIES CE-47.
Burda magazine download pdf free 2012. You'll find patterns for quilts, pillows, table runners, duvet covers, bags, purses, floor cushions, baby clothes, baskets, napkins, Christmas tree skirts, backpacks, place mats, hats, women's clothing, and much, much more.
FOR VX-2500 LTR SERIES. FOR VX-2500 LTR SERIES. FOR VX-2500 LTR SERIES. SVC-47 v1.00 ADJUSTMENT SOFTWARE. FOR VX-2500 LTR SERIES.
CE-49 v3.1.1.0. FOR VX-4000/5500/6000. CE-49 v3.3.0.0.
FOR VX-4000/5500/6000. CE-49 v3.3.7.0. FOR VX-4000/5500/6000.
CE-49 v4.0.6.0 FOR VX-4000/5500/6000. CVS-49 v16.8.0. FOR VX-4000/5500/6000. RADIO ADJUSTMENT. CE-49 v1.0.2.0. FIELD PROGRAMMER FOR VX-4000/5500/6000.
CE-49 v5.00 FOR VX-4000/5500/6000 (WINDOWS VISTA) NEW! FDUP FOR RF DECK FIRMWARE V3.04. FDUP FOR RF DECK FIRMWARE V4.08.
SVC49 V1.6.8.0 (VX-4000, VX-6000, VX-5500) ADJUSTMENT SOFTWARE. FW2WIN V1.08 FOR VX-4200 FIRMWARE V1.55 PACKAGE. CE-51 v 2.00W by Vertex - 2002. FOR VX-160E/180E - Europe.
CE-51 v 4.01W by Vertex. FOR VX-160E/180E - Europe. CE-51 v 5.00 by Vertex. FOR VX-160E/180E - Europe. FOR VX-3200/2500 CONVENTIONAL.
CE-52C V1.10. (VX-3208 & VX-2508 CHINA). CE-52EV v3.00B. FOR VX-3200/2500 CONVENTIONAL.
This clone editor CE52EV 3.00b has been modified to be able to program the special frequency channel to the VX-3200 radio as follows, = July 17th, 2003 Expanded the range of acceptable frequency as follows: 1. VHF C band: 148 - 174MHz - 130 - 200MHz (Ver 3.00b)@ 2. UHF D band: 450 - 490MHz - 430 - 490MHz (Ver 3.00b) 3. Delete frequency restriction beteen 406.000 - 406.100MHz CE-52E v4.41.
FOR VX-3200/2500 CONVENTIONAL. CE-52E v4.50. FOR VX-3200/2500 CONVENTIONAL.
CE-52E v4.71. FOR VX-3200/2500 CONVENTIONAL. SVC-52 v1.02. ADJUSTMENT SOFTWARE FOR VX-3200/2500 CONVENTIONAL. FW2S V1.33 FLASH ROM WRITING SOFT WITH VX-3200 FIRMWARE: 39ST0372 (V0372) PACKAGE. CE-53 v1.00W. CE-56 v1.00W-USA.
CE-59 v1.0W USA. FOR VX-4100E/4200E/VX820/VX920 SERIES.
CE-59 v1.01W USA. FOR VX-4100E/4200E/VX820/VX920 SERIES. CE-59 v1.20.00W USA. FOR VX-4100E/4200E/VX820/VX920 SERIES. CE-59 v2.10.00W USA. FOR VX-4100E/4200E/VX820/VX920 SERIES.
CE-59 v2.14.00W USA. FOR VX-4100E/4200E/VX820/VX920 SERIES. CE-59 v2.29.00W USA. FOR VX-4100E/4200E/VX820/VX920 SERIES.
CE-59 v3.00 VISTA USA. FOR VX-4100E/4200E/VX820/VX920 SERIES 2008 NEW! CE-60 v1.00W USA. FOR VXR-9000. CE-60 v1.03W USA. FOR VXR-9000.
CE-60 v1.04W USA. FOR VXR-9000. CE-60 v1.05W USA. FOR VXR-9000. FOR VXR-9000.
NEW FDUP FOR VXR-9000 V1.30. (FIRMWARE UPDATE TO V1.30). CE-62 LOOKING FOR THIS PROGRAM! FOR VX-2500E EUROPE. CE-64 v1.00W USA.
FOR VX-410/414/417/420/424/427. FOR VX-410/414/417/420/424/427. FOR VX-410/414/417/420/424/427.
FOR VX-410/414/417/420/424/427. FOR VX-410/VX-420 SERIES. FW2WIN V1.08 WITH AC050 V115 FIRMWARE PACKAGE FOR VX-410 SERIES. CE-65 v1.00W USA. FOR VX-530 SERIES.
CE-65 v1.02W USA. FOR VX-530 SERIES. SVC65 V1.00 SERVICE ALIGNMENT SOFTWARE FOR VX-530 SERIES. FW2WIN V1.06 WITH AC052 V105 FIRMWARE PACKAGE FOR VX-530 SERIES. CE-68 v1.1 USA & EUROPE. FOR HX-270 & HX-370 SERIES.
CE-71 v1.00 W, USA. FOR VXA300 SERIES. CE-73 v1.04W USA. VMDE-200 MDC1200 ENCODER/DECODER MODULE & VME-100 THE VME-100 IS A PLUG-IN ANI ENCODER CAPABLE OF ENCODING MDC1200, GE STAR OR DTMF ANI. CE-73 v1.05W USA. VMDE-200 MDC1200 ENCODER/DECODER MODULE & VME-100 THE VME-100 IS A PLUG-IN ANI ENCODER CAPABLE OF ENCODING MDC1200, GE STAR OR DTMF ANI.
CE-74 v1.00W USA. CE-75 v1.02W USA. CE-76 v2.01.13W USA. FOR VX7100, VX7200, VXP820/920 (APCO 25).
CE-76 v2.01.22W USA. FOR VX7100, VX7200, VXP820/920 (APCO 25). CE-76 v2.02.W USA. FOR VX7100, VX7200, VXP820/920 (APCO 25). CE-76 v2.03.10.W USA. FOR VX7100, VX7200, VXP820/920 (APCO 25).
FW2WIN P924V0109 (FIRMWARE FOR CE-76). CE-77 v1.0.0.0 FOR VX1700. CE-77 v1.1.0.0 FOR VX1700. FSW001 V1.02 (FIRMWARE FOR VX-1700). FOR VX427AE (VX420A SERIES-256 CHANNELS) NEW CE-82 v1.02w USA. FOR VX-2100/VX-2200.
CE-82 v1.03w USA. FOR VX-2100/VX-2200. CE-82 v1.04w USA. FOR VX-2100/VX-2200.
CE-82 v1.08w USA. FOR VX-2100/VX-2200. CE-82 v1.09w USA. FOR VX-2100/VX-2200CB MOBILES. CE-82 v1.10w USA. FOR VX-2100/VX-2200CB MOBILES.
CE-82 v1.12w USA. FOR VX-2100/VX-2200CB MOBILES. CE-82 v2.00w USA. FOR VX-2100/VX-2200CB MOBILES.
NEW FW2WIN V1.08 WITH FIRMWARE VX-2100 & 2200 V1.01 PACKAGE. CE-86 v1.01w USA. CE-86 v2.0 USA. CE-86 v2.01 USA.
FOR VX-350CHN (VX351 & VX354 CHINA). NEW CE-86 v2.02 USA. NEW CE-88 v1.00w USA. NEW CE-89 v1.03. FOR VXA-420A PASSPORT SERIES PORTABLES. NEW CE-91F v1.02 FOR VX-426CB HANDY RADIO.
LOOKING FOR THIS PROGRAM. NEW CE-95 v1.01 FOR VX-351 - PMR446-500mW-EUROPE. (FOR VISTA), 2008.
NEW VX-2100/VX2200 FW2WIN v1.10 FIRMWARE UPGRADE TOOL v1.09. NEW FDUP FOR RF DECK FW ( VX-4000/6000 RF DECK FIRMWARE UPDATE verx. Xx to ver 2.2.0 ). FDUP FOR CONTROL HEAD FW ( VX-4000/6000 PANEL FIRMWARE UPDATE verx. Xx to ver 2.0.1 ).
FIRMWARE TOOL UPGRADE FOR VX-600/800/900 RADIOS. NEEDS FIF-8 FLASH ROM ADAPTER.
FDUP VX4000/VX6000 series RF Deck Firmware Update verx. Xx to ver4.2 2008 PFDUP VX4000/VX6000 series Panel Firmware Update verx.xx to ver3.04 2008 FT-10 Programmer. RT Systems, Inc.
FT-11 Programmer. RT Systems, Inc. FT-50 v.1.04.
FT-50 v.1.05. FT-50 v.1.07. FT-50-TOOLS v1.0 1999. FT-50 Manager. Goran Vlaski. FT-51 Programmer.
RT Systems, Inc. FT-90 Radio Programming Trial Version. By RT Systems, Inc. FT-212/712 CAT Program v3.1. Dos and Windows.
FT-736R YASCAN-11. FT-757GX MARK I CAT v1.0. FT-767GX CAT Program v1.0 4 Feb 1990. FT-676GX CAT Tuning Program by WA3AKK.
31 March 1996. FT-920 Scope v1.0. FT-920 Scan920. FT-980 CAT980 by K5EF. FT-990 CAT Program for FT-990/890/840/900/920/1000MP. DOS and WIN 3.1,for WIN95-exit Windows.
FT-1000m3 simple program for the FT-1000 transceiver. FT-2600 TRIAL PROGRAM v1.00 2000. FT-3000 Programmer. RT Systems,Inc. FT-7800 FTB7800 ( ID & REGISTRATION KEY INCLUDED ). FT-8100 v2.03 1999. FT-8500 v1.00 1995.
FTC-2640 calculation program. GX-1710 v1.10 9 Jan 1998. GX-2000 ROM WRITER Program A340P. GX-2000 ROM WRITER v1.9. GX-3000 U/V/K-HX400 U/V/K v1.6. GX-3000 v/u Windows editor.
GX-3010DP v1.7. (Trunk Mobile 800MHz Motorola & Johnson Systems).
GX-3030TJ v2.0. Firmware version: N2.0 (Trunk 800MHz). GX-3030TM v1.0. (Trunk 800MHz).
GX-4800UT (F3) ADJUSTMENT MENU FOR THE GX4800UT v1.20. GX4800UT Trunking Software v1.4 Copyright (c) 1997.
GX4800UT Trunking Software v1.6 Copyright (c) 1997. GX4800UT Trunking Software v2.0 Copyright (c) 1998. GX4800UT with PassPort Trunking Software v1.0 Copyright (c) 1999.
GX5800T Trunking Software v1.3 Copyright (c) 1995. ADJUSTMENT FOR THE GX5800T. GX-5810T TUNE v0.0 GX-5810T TUNE v1.0. GX-5810T+ v1.2 (Trunk 800MHz). GX-5810T v1.3. (Trunk 800MHz).
GX-5850T Trunking Software. HX-120V/HX-120U v1.31. HX-140 v1.00 1998. HX-240U/V v1.9.
1992 (PPS-240). HX-241U/V v1.5 1992. HX-260 PPS v1.03. ( BUILD-0015 ). HX-290U/V v1.00 (PPS-290) 1998.
HX-290U/V v1.00 (PPS-290) 1999. HX-292UT TRUNK PERSONAL PROGRAMMING SYSTEM, v1.11 MARANTZ JAPAN, ( MODELS: F1/F3/F5/SP ). HX-381 PPS Rel.1.0. HX345 & GX2010 v6. HX340 v1.7 PPS340. HX347 v4.00 ( STANDARD VX347 FOR U.K.
HX347 v6.00 ( STANDARD VX347 FOR U.K. HX-381 PPS Rel.2.2 HX-390-A/B/C/D/E/F FORMAT PROGRAM Rel.1.2. HX-390-A/B/C/D/E/F FORMAT PROGRAM Rel.1.3. SC-390 STABO (RE-BADGED STANDARD HX390) V1.2 & V1.3 GERMAN Programm. SC-390 STABO (RE-BADGED STANDARD HX390) V1.4MH GERMAN. HX-428UT TUNE v1.1.
HX-530U/V v1.0 (PPS-530) 1990. HX-580T v1.0. HX-580T-TUNE v.1.2. HX-580T v1.5. HX-580T v2.8. HX-580T v2.9. HX-581T v1.8.
HX-582T v1.7. HX-585T TUNE v1.1. HX-585T v1.0. HX-590T TUNE v2.0. HX-591T UHF 8XX MHZ PROGRAMMER. PL-2303 USB DRIVER SOFTWARE.
PPS-340U/V v1.5 for HX-340/347V(TB)Communique London U.K. PPS-340U/V v1.7 for HX-340/347V(TB)Communique London U.K.
PPS-340U/V v4.5. Release: 1992. PPS-341 v1.1. for HX-341/347+ PPS-440U/V v1.0 for HX-440 1991.
PPS-440U/V v1.7. PPS-440U/V v1.9 for HX-440 1992.
PPS-530U/V v4.0 for HX-530 1990. PPS-1500U/V v1.0 Release: 1990. PPS -1500U/V for GX-1500 v1.3 1991. PPS -1500U/V for GX-1500 v1.5 1991. PPS-1500U/V for GX-1500 v4.4. PPS-1510U/V Trunking v2.06b 14 May 1996. PPS-1510U/V for GX-1510U/V v2.08b.
23 Sept 1996. PPS-2000U/V v1.0.
PPS-2000U/V v1.5. For GX-2000/2007U(TB)Communique London U.K. PPS-2000U/V v4.3. PPS-3200U/V v1.7 1992.
PPS-3200U/V v1.9 1992. PPS-RPT Repeater Programming Utility. For: RPT-31/32/34/33/38 RTL-2007 PROGRAMMER, 1997. ( SMC-2516/SMC-2546, USES FYG-4 PROGRAMMER ).
S.C.C.DAT v1.5. SPARE PARTS ENQUIRY. SMC2546L8 (UHF) OR SMC2516L8 (VHF) SPECIAL WIDE BAND VERSION SOFTWARE.
FYG-4 EMULATOR MK II. VR-120 commander VR-500 commander VR-500 ADMS-3 v1.05 RTSystems VR-5000 Scanning Receiver Control Program VR5K v beta0.9.6. VX-3 FTBVX3 v1.10. MEMEORY MANAGEMENT BY G4HFG (USERNAME & PASSWORD INCLUDED).
VX-5R/VX-1R/FT-50 Programmer. VX-5 EASY EDITOR by KF4FDT v1.70. VX-7 Commander v1.0 beta 10. VX-7 Commander v1.26. VX-110/150 Programmer for Windows 95/98, v1.04 2000. VX-110/150 ARDTS-150, Amateur Radio Data Transfer System v1.01 1999. RT-Systems Inc.
VX-310 PPS v1.01. VX-429 - 2509PRO MPT1327 V1.15. (350-390 MHZ LOW POWER HANDHELD FOR CHINESE POLICE).
VERTEX Programming Software v6.22. VERTEX Programming Software v6.24 for FTH-2070/FTH-2008/7008/2009/7009/VX-500-Vhf-Uhf/FTL-1011/2011/7011-4/1/24/99 Channels/FTL-8011- P3/P2/VX-200-VHF/UHF/VX-5000-Repeater-Vhf-Uhf. VERTEX Programming Software v7.2 for FTH-2070/VX-200/VX-500/FTL-1011/2011/7011-4/12/24 Channel/FTL-1011/2011/7011-99 Channel/VXR-5000 Repeater/VX-2000/VX-3000. VERTEX-ANTRACIT-RPS-CT42A for: VX-10-ce14/VX-300-ce18/VX-160-180-ce44/VX-400-ce24/VX-400 ALIGMENT.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |